A fuzzy logic PI control with feedforward compensation for hydrogen pressure in vehicular fuel cell system

In a vehicular fuel cell system, alternative load and frequent purge action can lead to anode pressure varies with the hydrogen mass flow fluctuation. It's crucial to control the pressure difference between anode and cathode within a reasonable range to avoid adverse phenomena such as membrane failure, reactant starvation, or even water management fault. In this paper, an improved proportional integrative (PI) controller by the fuzzy logic technique that considers the engineer experience and knowledge on the hydrogen supply system behavior is proposed for hydrogen pressure control, in which the PI parameters are tuned by a fuzzy decision process. Furthermore, load current and purge action regarded as input disturbances are applied for feedforward compensation to reduce the pressure response hysteresis. A hydrogen supply subsystem based on the proportional valve is modeled, and corresponding parameters are determined by analyzing the response time and steady pressure fluctuation. The performance of the conventional PI controller, the fuzzy logic PI (FLPI) controller and fuzzy logic PI with feedforward (FLPIF) controller is validated. The presented results indicated that the FLPI controller significantly improves the dynamic response of hydrogen pressure compared to the PI controller, and the FLPIF controller can further reduce overshoot caused by disturbance. Finally, the proposed FLPIF controller is implemented on a rapid prototype platform of the hydrogen supply subsystem and an actual fuel cell system, exhibiting satisfactory performance.     

Development of autonomous monitoring and performance evaluation system of grid-tied photovoltaic station

This work aims to improve the existing monitoring systems MS for two grid-connected PV stations GCPVS of URERMS ADRAR, to eliminate its limitations. This improvement consists of developing an MS which is used for two PV stations with different configurations. This MS contains new LabVIEW-based monitoring software for visualizing real-time measured data and evaluating GCPVS performance. In addition, it illustrates the 2D and 3D real-time relationships of PV system parameters, which allow us to understand the dynamic behavior of PV system components. This developed monitoring software synchronizes also the various data acquisition units DAU of GCPVS, allowing simultaneous data access.To perform a reliable performance analysis and a comparative study of different GCPVS based on accurate measurements, the sensor's calibration is performed with its DAU. The MS autonomy is ensured by integrating developed PV-UPS. A graphical user interface is provided for the evaluation of PV-UPS performance.     

Thermal analysis and management of proton exchange membrane fuel cell stacks for automotive vehicle

The thermal management of a proton exchange membrane fuel cell (PEMFC) is crucial for fuel cell vehicles. This paper presents a new simulation model for the water-cooled PEMFC stacks for automotive vehicles and cooling systems. The cooling system model considers both the cooling of the stack and cooling of the compressed air through the intercooler. Theoretical analysis was carried out to calculate the heat dissipation requirements for the cooling system. The case study results show that more than 99.0% of heat dissipation requirement is for thermal management of the PEMFC stack; more than 98.5% of cooling water will be distributed to the stack cooling loop. It is also demonstrated that controlling cooling water flow rate and stack inlet cooling water temperature could effectively satisfy thermal management constraints. These thermal management constraints are differences in stack inlet and outlet cooling water temperature, stack temperature, fan power consumption, and pump power consumption.     

Techno-economic analysis of hydrogen energy for renewable energy power smoothing

With the increasing proportion of renewable energy (mainly wind power and photovoltaic) connected to the grid, the fluctuation of renewable energy power brings great challenges to the safe and reliable operation of power grid. As a clean, low-carbon secondary energy, hydrogen energy is applied in renewable energy (mainly wind power and photovoltaic) grid-connected power smoothing, which opens up a new way of coupling hydrogen storage energy with renewable energy. This paper focuses on the optimization of capacity of electrolyzers and fuel cells and the analysis of system economy in the process of power output smoothing of wind/photovoltaic coupled hydrogen energy grid-connected system. Based on the complementary characteristics of particle swarm optimization (PSO) and chemical reaction optimization algorithm (CROA), a particle swarm optimization-chemical reaction optimization algorithm (PSO-CROA) are proposed. Aiming at maximizing system profit, the capacity of electrolyzers and fuel cells are constrained by wind power fluctuation, and considering environmental benefits, government subsidies and time value of funds, the objective function and its constraints are established. According to the simulation analysis, by comparing the calculated results with PSO and CROA, it shows that PSO-CROA effectively evaluates the economy of the system, and optimizes the optimal capacity of the electrolyzers and fuel cells. The conclusion of this paper is of great significance for the application of hydrogen energy storage in the evaluation of power smoothness and economy of renewable energy grid connection and the calculation of economic allocation of hydrogen energy storage capacity.     

Clinical significance of contact lens related changes of ocular surface tissue observed on optical coherence images

PurposeTo investigate the relationship between the real contact lens imprint into the conjunctival tissue, observed by optical coherence tomography (OCT) and conjunctival staining and contact lens wearing comfort.Methods17 participants (mean age = 26.6 SD ± 3.6 years; 7 females) were fitted with three different contact lenses base curves of the same silicone hydrogel custom lens type (Visell 50; Hecht Contactlinsen, Au, Germany) in a randomised order. One lens was optimally fitted according to the manufacturer's recommendation, one fitted 0.4 mm flatter and one fitted 0.4 mm steeper. After 4 h of lens wear the contact lens edge in the area of the conjunctiva was imaged nasally and temporally using OCT (Optovue iVue SD-OCT). To correct the artefact due to optical distortion with OCT, the imprint of all worn lenses was measured on a glass plate afterwards. Conjunctival staining in the limbal region after 4 h of lens wear was classified using the CCLRU Grading Scale. Comfort scoring was based on visual analog scales from 0 (very poor) to 100 (excellent).ResultsThe mean conjunctival imprint of all contact lens edges was 32.0 ± 8.1 μm before and 7.3 ± 6.5 μm after distortion correction of the OCT images. The distortion corrected conjunctival imprint with the 0.4 mm steeper lens (11.5 ± 6.2 μm) was statistically significantly greater compared to the optimally fitted lens (6.5 ± 5.9 μm) (One-way ANOVA followed Tukey-test; p = 0.017) and greater compared to the 0.4 mm flatter lens (3.9 ± 5.3 μm) (p < 0.001). There was no statistically significant difference between the optimally fitted lens and the 0.4 mm flatter lens (p = 0.209). The nasally measured imprint (11.4 ± 9.0 μm) was significantly greater than the temporally measured (3.3 ± 7.6 μm) (p < 0.001). There was no statistically significant correlation between the amount of conjunctival imprint and the graded conjunctival staining (p = 0.346) or the wearer’s comfort (p = 0.735).ConclusionsContact lens edges imaged by OCT exhibited displacement artefacts. The observed conjunctival imprints are a combination of real conjunctival compression and artefacts. A deeper imprint of the contact lens into the conjunctiva caused by a steeper base curve was not related to clinically significant staining or changes in comfort after 4 h of lens wear. The observed differences between nasal and temporal imprint are likely to be caused by variations of conjunctival thickness and the shape of the underlying sclera.     

电商平台产品共同购买网络的影响因素研究

共同购买网络的推荐系统应用越加广泛，仅基于网络内生结构变量研究其共同购买链接的经济意义已有局限，故加入网络口碑这一外生变量，进行更全面的分析。采用了社会网络方法中指数随机图模型进行建模，主要围绕产品销售量、产品入度、差评率和评论数4个方面因素，探究其对共同购买网络中共同购买链接形成的影响。结果显示，销售量、产品入度和评论数对共同购买链接形成的影响呈正比关系，而差评率则会显著地降低产品共同购买的几率。该指数随机图构建出的共同购买网络为在线电商平台管理网络口碑和推荐系统优化设计提供有益参考。     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

Mechanical properties of Al2O3 and Al2O3/Al with Gyroid structure obtained by stereolithographic additive manufacturing and melt infiltration

To obtain both plasticity and toughness of the material at the same time, various manufacturing techniques of ceramic-metal composites and structures have been studied. In this work, a bio-inspired Al₂O₃ ceramic scaffold with Gyroid structure was designed and prepared by stereolithographic (SL) additive manufacturing, then the Al₂O₃/Al ceramic-metal hybrid structure was prepared by infiltrating molten Al into the Al₂O₃ ceramic structure. The performances of the Al₂O₃ ceramic scaffold and the Al₂O₃/Al ceramic-metal hybrid structure were compared and analyzed by a quasi-static compression experiment. The quasi-static compressive strength of the pristine Al₂O₃ scaffold was 14.36 MPa, while that of the Al₂O₃/Al ceramic-metal hybrid structure was up to 89.06 MPa. Moreover, the plasticity of the Al₂O₃/Al ceramic-metal hybrid structure was much higher than that of the Al₂O₃ scaffold. During compression, the Al₂O₃/Al ceramic-metal hybrid structure had excellent energy absorption, reaching up to 2569.16 KJ/m³, 15 times that of the Al₂O₃ scaffold. Therefore, this method can obtain materials with excellent ductility and toughness.     

我国鲜食玉米标准体系及营养标准研究

近年来我国鲜食玉米产业发展迅猛, 但同时也暴露出诸多产业乱象。梳理现有鲜食玉米标准体系是促进产业标准化、规范化的重要举措。本文通过对我国现行鲜食玉米标准进行梳理, 总结出目前我国鲜食玉米标准体系中抽样及一般性检测标准较完善、技术规程体系成熟、标准体系框架已建立的特点; 同时提出我国鲜食玉米标准体系存在技术规程标准内容重复、品质分级标准混乱、缺乏营养评价指标相关标准、感官评价标准混乱、缺乏甜糯玉米和笋玉米的相关标准、标准体系结构不合理等的问题; 并针对上述问题提出对应应统一技术规程标准, 建立营养评价体系, 统一品质分级标准, 统一感官评价指标, 完善甜糯玉米和笋玉米相关标准的解决办法。为鲜食玉米标准体系的建设及规范化提供参考和建议。     

A three-dimensional surface measurement system implemented with Gaussian process based adaptive sampling

Self-adaptive surface measurements that can reduce data redundancy and improve time efficiency are in high demand in many fields of science and technology. For this purpose, a system implemented with Gaussian process (GP) adaptive sampling is developed. The non-parametric GP model is applied to reconstruct the topography and guide the subsequent sampling position, which is determined from the inference uncertainty estimation. A criterion is proposed to terminate the GP adaptive measurement automatically without any prior model or data of the topography. Experiments on typical surfaces validate the intelligence, adaptability, and high accuracy of the GP method along with the stabilization of the automatic iteration termination. Compared with traditional raster sampling, data redundancy is reduced and the time efficiency is improved without sacrificing the surface reconstruction accuracy. The proposed method can be implemented in other systems with similar measurement principles, thus benefitting surface characterizations.